各位大牛您们好:
今天烧写emmc的时候遇到了问题,就是网卡会断掉,并且一直在27%停止,看之前也有人问过,可惜没有解决的方法,请大牛们帮帮忙了。
This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
我之前测试的烧nand的时候有发现过类似的情况,你看下参考下面的方法能否解决你的问题。
在这个帖子中第四点已经列出来了:
http://www.deyisupport.com/question_answer/dsp_arm/sitara_arm/f/25/t/52381.aspx
在u-boot-spl-restore.bin下载运行成功后,下载u-boot-restore.img时,网络一直在发IP请求,却没有得到回应,请参考以下解决方案:在操作过程中,插上USB时能在主机上找到USB RNDIS网络,默认时配置该网络IP为192.168.2.1。在烧写的不同阶段,部分主机会将该网络会识别成另外的USB RNDIS网络,因此,与之前的网络不同且没有IP配置,此时只需要再配置该网络的IP为192.168.2.1,即可正常使用(可能会弹出提示:该IP被未使用的网络占用,是否要清除未使用的网络?此时选择否)。
这点是照做了把:该IP被未使用的网络占用,是否要清除未使用的网络?此时选择否
另外,在烧写的过程中,板卡串口终端上面是会有信息输出的,你把串口输出的log信息发上来看一下。
您好:那个照做了,就是一开始还是27%的后来又成0%了。
usb_ether
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 78:a5:04:dd:29:1f
HOST MAC de:ad:be:af:00:00
RNDIS ready
ERROR: The remote end did not respond in time.
at ether.c:2397/usb_eth_init()
Problem booting with BOOTP
### ERROR ### Please RESET the board ###
从log上面看,你是不是没有装那个patch啊?
还是那个帖子中的第三条:
在Uniflash进行u-boot-spl-restore.bin的下载时,如果出现usb网络反应超时,请确认是否已经安装我们的usb patch:0001-u-boot-Change-default-cdc_connect_timeout-to-15s.patch。另外,一定要确认网络防火墙和杀毒软件是否已经关闭。
您好,我那个uniflash烧写有了进展上面貌似烧好了,可是进度条没有,请帮我看下下面log的是不是成功了.
BOOTP broadcast 3
Using usb_ether device
TFTP from server 192.168.2.1; our IP address is 192.168.2.2
Filename 'u-boot-restore.img'.
Load address: 0x807fffc0
Loading: *#########################
667 KiB/s
done
Bytes transferred = 365104 (59230 hex)
U-Boot 2013.01.01 (Dec 19 2014 - 14:57:53)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 78:a5:04:dd:29:1f
HOST MAC de:ad:be:af:00:00
RNDIS ready
musb-hdrc: peripheral reset irq lost!
high speed config #2: 2 mA, Ethernet Gadget, using RNDIS
USB RNDIS network up!
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.2.2
using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC 78:a5:04:dd:29:1f
HOST MAC de:ad:be:af:00:00
RNDIS ready
high speed config #2: 2 mA, Ethernet Gadget, using RNDIS
USB RNDIS network up!
Using usb_ether device
TFTP from server 192.168.2.1; our IP address is 192.168.2.2
Filename 'uImage'.
Load address: 0x81000000
Loading: *T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
1.1 MiB/s
done
Bytes transferred = 12281160 (bb6548 hex)
## Booting kernel from Legacy Image at 81000000 ...
Image Name: Linux-3.2.0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 12281096 Bytes = 11.7 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 3.2.0 (zhouqun@zhouqun-desktop) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #4 Sat Dec 20 12:19:05 CST 2014
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing
done.
Mon Feb 17 19:03:00 UTC 2014
Collected errors:
* opkg_conf_load: Could not create lock file /var/lib/opkg/lock: No such fil
INIT:
Entering runlevel: 5
Starting syslogd/klogd: done
*********************************
*******************
*****************************
***********************
Sitara Flash Fetcher Sc
ript - 07/28/2014
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
Sending select for 192.168.2.5...
Lease of 192.168.2.5 obtained, lease time 600
/etc/rc5.d/S99fetcher.sh: line 21: [: ==: unary operator expected
Getting flasher script from server:
BusyBox v1.20.2 (2014-02-17 12:53:20 CST) multi-call binary.
Usage: tftp [OPTIONS] HOST [PORT]
Unable to fetch debrick script! Exiting...
Stopping Bootlog daemon: bootlogd.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am335x-evm ttyO0
Arago 2013.05 am335x-evm ttyO0
am335x-evm login: root